Outboardman...take a look at this plz.

Duck boats and duck boat blinds!

Outboardman...take a look at this plz.

Postby aunt betty » Thu Oct 05, 2017 1:15 pm

My transom has cracked again. Third time now.
First it cracked on the corners.
Started doing it again so I took it to the welder and he put that big piece on the center. It's u-shaped and wraps around.
Now it's cracking at the edges of the piece.

The metal there is very thin and sort of just covers the plywood.
The question is...should I even bother having it re-welded?
It's cracking in the HAZ (heat affected zone)

Weld it up and the cracks will just form again at the edge of the new weld.
Time to give up?
Run it til it falls apart?

Telling mama I need a new jon boat might not be such a good idea at this time.
20171003_135627.jpg
20171003_135638.jpg
YOU MUST REGISTER TO VIEW THIS IMAGE.
I've heard that it's incredibly stupid to **** around with a crazy man's head.
User avatar
aunt betty
 
Posts: 13878
Joined: Tue Feb 05, 2013 9:37 pm
Location: East Side

Re: Outboardman...take a look at this plz.

Postby aunt betty » Thu Oct 05, 2017 1:16 pm

If you want better pictures of the whole transom let me know.
I've heard that it's incredibly stupid to **** around with a crazy man's head.
User avatar
aunt betty
 
Posts: 13878
Joined: Tue Feb 05, 2013 9:37 pm
Location: East Side

Re: Outboardman...take a look at this plz.

Postby aunt betty » Thu Oct 05, 2017 2:04 pm

Took some pics to show how well-braced the transom is.
IMO its run it til it falls apart.
The wood in the transom is solid and has been doing the work for decades.
Boat is 39 yrs old.

20171005_134045.jpg
20171005_133710.jpg
YOU MUST REGISTER TO VIEW THIS IMAGE.
I've heard that it's incredibly stupid to **** around with a crazy man's head.
User avatar
aunt betty
 
Posts: 13878
Joined: Tue Feb 05, 2013 9:37 pm
Location: East Side

Re: Outboardman...take a look at this plz.

Postby Deltaman » Thu Oct 05, 2017 2:42 pm

AB, you could always more plate to both sides to strengthen. Had a similar issue with an old aluminum boat when I was in school and funds were tight. I just added a 1 X 4 treated board across the inside of the transom, and clamped the motor down over it. That was enough to keep it stiff enough along the top of the transom to hold. Somewhat of a Democratic fix, but it worked.
"It ain't what you don't know that gets you in trouble. It's what you know for sure, that just ain't so"
Mark Twain
User avatar
Deltaman
 
Posts: 819
Joined: Wed Nov 06, 2013 8:55 am
Location: Mobile, AL

Re: Outboardman...take a look at this plz.

Postby aunt betty » Thu Oct 05, 2017 3:10 pm

Thinking about adding a 1.5" square tube on top. Would have to cut it to fit because of that piece the welder added.
Then I could raise the motor up another 1.5 inches too.
The way it runs now...the fin on the motor is about an inch and a half low.

The metal is there just for looks sort of. No way is that structural as it's only 1/16th thick aluminum...maybe .100".
Something like that.
The plywood is the beef in that assembly until that u-plate was added. Gee that stiffened it up.
I think I'll just run it and watch that crack until it starts growing.

Now before you worry about my safety...I'd much rather die in my favorite hunting lake than the fema camp that my future holds for me.
I've heard that it's incredibly stupid to **** around with a crazy man's head.
User avatar
aunt betty
 
Posts: 13878
Joined: Tue Feb 05, 2013 9:37 pm
Location: East Side

Re: Outboardman...take a look at this plz.

Postby aunt betty » Tue Oct 10, 2017 12:50 pm

Got it welded up again.
Ready to go. 18 days and it's on.
20171010_120647.jpg

20171010_122233.jpg
YOU MUST REGISTER TO VIEW THIS IMAGE.
I've heard that it's incredibly stupid to **** around with a crazy man's head.
User avatar
aunt betty
 
Posts: 13878
Joined: Tue Feb 05, 2013 9:37 pm
Location: East Side


Return to Duck Boat & Mud Motor Forum

Who is online

Users browsing this forum: No registered users and 4 guests